-- Network Working Group T. Brown, Editor
-- Request for Comments: 1604 Bell Communications Research
-- Obsoletes: 1596 March 1994
-- Category: Standards Track
--
--
-- Definitions of Managed Objects
-- for Frame Relay Service
--FRNETSERV-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,NOTIFICATION-TYPE,Counter32,Integer32,TimeTicksFROM SNMPv2-SMI
DisplayString,PhysAddress,TimeStamp,RowStatusFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
ifIndex, transmission FROM RFC-1213;
frnetservMIB MODULE-IDENTITYLAST-UPDATED"9311161200Z"ORGANIZATION"IETF Frame Relay Network MIB Working Group"CONTACT-INFO" Tracy A. Brown
Bellcore
331 Newman Springs Rd.
Red Bank, NJ 07701 USA
Tel: 1-908-758-2107
Fax: 1-908-758-4177
E-mail: tacox@mail.bellcore.com."DESCRIPTION"The MIB module to describe generic objects for
Frame Relay Network Service."::={ transmission 44}IfIndex::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The value of this object identifies the
interface for which this entry contains
management information. The value of this
object for a particular interface has the same
value as the ifIndex object, defined in RFC
1213, for the same interface."SYNTAXInteger32frnetservObjects OBJECTIDENTIFIER::={ frnetservMIB 1}frnetservTraps OBJECTIDENTIFIER::={ frnetservMIB 2}-- The Frame Relay Service Logical Port Group-- the Frame Relay Logical Port Group-- This table is an interface specific addendum-- to the generic ifTable from MIB-II.frLportTable OBJECT-TYPESYNTAXSEQUENCEOF FrLportEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"The Frame Relay Logical Port Information table."::={ frnetservObjects 1}frLportEntry OBJECT-TYPESYNTAX FrLportEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the Frame Relay Logical Port
Information table."INDEX{ ifIndex }::={ frLportTable 1}
FrLportEntry ::=SEQUENCE{
frLportNumPlan
INTEGER,
frLportContact
DisplayString,
frLportLocation
DisplayString,
frLportType
INTEGER,
frLportAddrDLCILen
INTEGER,
frLportVCSigProtocol
INTEGER,
frLportVCSigPointer
OBJECTIDENTIFIER}frLportNumPlan OBJECT-TYPESYNTAXINTEGER{other(1),e164(2),x121(3),none(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the network
address numbering plan for this UNI/NNI logical
port. The network address is the object
ifPhysAddress. The value none implies that there
is no ifPhysAddress. The SNMP proxy-agent will
return an octet string of zero length for
ifPhysAddress. The value other means that an
address has been assigned to this interface, but
the numbering plan is not enumerated here."::={ frLportEntry 1}frLportContact OBJECT-TYPESYNTAXDisplayString(SIZE(0..255))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the network
contact for this UNI/NNI logical port."::={ frLportEntry 2}
frLportLocation OBJECT-TYPESYNTAXDisplayString(SIZE(0..255))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the Frame
Relay network location for this UNI/NNI logical
port."::={ frLportEntry 3}frLportType OBJECT-TYPESYNTAXINTEGER{uni(1),nni(2)}MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The value of this object identifies the type of
network interface for this logical port."::={ frLportEntry 4}frLportAddrDLCILen OBJECT-TYPESYNTAXINTEGER{twoOctets10Bits(1),threeOctets10Bits(2),threeOctets16Bits(3),fourOctets17Bits(4),fourOctets23Bits(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the Q.922
Address field length and DLCI length for this
UNI/NNI logical port."::={ frLportEntry 5}frLportVCSigProtocol OBJECT-TYPESYNTAXINTEGER{none(1),lmi(2),ansiT1617D(3),ansiT1617B(4),ccittQ933A(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the Local
In-Channel Signaling Protocol that is used for
this frame relay UNI/NNI logical port."::={ frLportEntry 6}frLportVCSigPointer OBJECT-TYPESYNTAXOBJECTIDENTIFIERMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object is used as a pointer to
the table that contains the Local In-Channel
Signaling Protocol parameters and errors for this
UNI/NNI logical port. See the Frame Relay
Management VC Signaling Parameters and Errors
Group."::={ frLportEntry 7}-- the Frame Relay Management VC Signaling Group-- This Group contains managed objects for the-- Local In-Channel Signaling Parameters and-- for signaling errors.
frMgtVCSigTable OBJECT-TYPESYNTAXSEQUENCEOF FrMgtVCSigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Frame Relay Management VC Signaling
Parameters and Errors table."::={ frnetservObjects 2}frMgtVCSigEntry OBJECT-TYPESYNTAX FrMgtVCSigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the Frame Relay Management VC
Signaling Parameters Errors table."INDEX{ ifIndex }::={ frMgtVCSigTable 1}
FrMgtVCSigEntry ::=
SEQUENCE{
frMgtVCSigProced
INTEGER,
frMgtVCSigUserN391
INTEGER,
frMgtVCSigUserN392
INTEGER,
frMgtVCSigUserN393
INTEGER,
frMgtVCSigUserT391
INTEGER,
frMgtVCSigNetN392
INTEGER,
frMgtVCSigNetN393
INTEGER,
frMgtVCSigNetT392
INTEGER,
frMgtVCSigNetnN4
INTEGER,
frMgtVCSigNetnT3
INTEGER,
frMgtVCSigUserLinkRelErrors
Counter32,
frMgtVCSigUserProtErrors
Counter32,
frMgtVCSigUserChanInactive
Counter32,
frMgtVCSigNetLinkRelErrors
Counter32,
frMgtVCSigNetProtErrors
Counter32,
frMgtVCSigNetChanInactive
Counter32}frMgtVCSigProced OBJECT-TYPESYNTAXINTEGER{u2nnet(1),bidirect(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the Local
In-Channel Signaling Procedure that is used for
this UNI/NNI logical port. The UNI/NNI logical
port can be performing only user-to-network
network-side procedures or bidirectional
procedures."
::={ frMgtVCSigEntry 1}frMgtVCSigUserN391 OBJECT-TYPESYNTAXINTEGER(1..255)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the User-side
N391 full status polling cycle value for this
UNI/NNI logical port. If the logical port is not
performing user-side procedures, then this value
is equal to noSuchName. This object applies to
Q.933 Annex A and T1.617 Annex D."DEFVAL{6}::={ frMgtVCSigEntry 2}frMgtVCSigUserN392 OBJECT-TYPESYNTAXINTEGER(1..10)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the User-side
N392 error threshold value for this UNI/NNI
logical port. If the logical port is not
performing user-side procedures, then this value
is equal to noSuchName. This object applies to
Q.933 Annex A and T1.617 Annex D."DEFVAL{3}::={ frMgtVCSigEntry 3}frMgtVCSigUserN393 OBJECT-TYPESYNTAXINTEGER(1..10)MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The value of this object identifies the User-side
N393 monitored events count value for this UNI/NNI
logical port. If the logical port is not
performing user-side procedures, then this value
is equal to noSuchName. This object applies to
Q.933 Annex A and T1.617 Annex D."DEFVAL{4}::={ frMgtVCSigEntry 4}frMgtVCSigUserT391 OBJECT-TYPESYNTAXINTEGER(5..30)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the User-side
T391 link integrity verification polling timer
value for this UNI/NNI logical port. If the
logical port is not performing user-side
procedures, then this value is equal to
noSuchName. This object applies to Q.933 Annex A
and T1.617 Annex D."DEFVAL{10}::={ frMgtVCSigEntry 5}frMgtVCSigNetN392 OBJECT-TYPESYNTAXINTEGER(1..10)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the Network-
side N392 error threshold value (nN2 for LMI) for
this UNI/NNI logical port. If the logical port is
not performing network-side procedures, then this
value is equal to noSuchName. This object applies
to Q.933 Annex A, T1.617 Annex D and LMI."
DEFVAL{3}::={ frMgtVCSigEntry 6}frMgtVCSigNetN393 OBJECT-TYPESYNTAXINTEGER(1..10)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the Network-
side N393 monitored events count value (nN3 for
LMI) for this UNI/NNI logical port. If the
logical port is not performing network-side
procedures, then this value is equal to
noSuchName. This object applies to Q.933 Annex A,
T1.617 Annex D and LMI."DEFVAL{4}::={ frMgtVCSigEntry 7}
frMgtVCSigNetT392 OBJECT-TYPESYNTAXINTEGER(5..30)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the Network-
side T392 polling verification timer value (nT2
for LMI) for this UNI/NNI logical port. If the
logical port is not performing network-side
procedures, then this value is equal to
noSuchName. This object applies to Q.933 Annex A,
T1.617 Annex D and LMI."DEFVAL{15}::={ frMgtVCSigEntry 8}frMgtVCSigNetnN4 OBJECT-TYPESYNTAXINTEGER(5..5)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the Network-
side nN4 maximum status enquires received value
for this UNI/NNI logical port. If the logical
port is not performing network-side procedures or
is not performing LMI procedures, then this value
is equal to noSuchName. This object applies only
to LMI and always has a value of 5."::={ frMgtVCSigEntry 9}frMgtVCSigNetnT3 OBJECT-TYPESYNTAXINTEGER(5 | 10 | 15 | 20 | 25 | 30)MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The value of this object identifies the Network-
side nT3 timer (for nN4 status enquires received)
value for this UNI/NNI logical port. If the
logical port is not performing network-side
procedures or is not performing LMI procedures,
then this value is equal to noSuchName. This
object applies only to LMI."DEFVAL{20}::={ frMgtVCSigEntry 10}frMgtVCSigUserLinkRelErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of user-side local in-channel
signaling link reliability errors (i.e., non-
receipt of Status/Status Enquiry messages or
invalid sequence numbers in a Link Integrity
Verification Information Element) for this UNI/NNI
logical port. If the logical port is not
performing user-side procedures, then this value
is equal to noSuchName."::={ frMgtVCSigEntry 11}frMgtVCSigUserProtErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of user-side local in-channel
signaling protocol errors (i.e., protocol
discriminator, message type, call reference, and
mandatory information element errors) for this
UNI/NNI logical port. If the logical port is not
performing user-side procedures, then this value
is equal to noSuchName."::={ frMgtVCSigEntry 12}frMgtVCSigUserChanInactive OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times the user-side channel was
declared inactive (i.e., N392 errors in N393
events) for this UNI/NNI logical port. If the
logical port is not performing user-side
procedures, then this value is equal to
noSuchName."::={ frMgtVCSigEntry 13}frMgtVCSigNetLinkRelErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of network-side local in-channel
signaling link reliability errors (i.e., non-
receipt of Status/Status Enquiry messages or
invalid sequence numbers in a Link Integrity
Verification Information Element) for this UNI/NNI
logical port. If the logical port is not
performing network-side procedures, then this
value is equal to noSuchName."::={ frMgtVCSigEntry 14}frMgtVCSigNetProtErrors OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of network-side local in-channel
signaling protocol errors (i.e., protocol
discriminator, message type, call reference, and
mandatory information element errors) for this
UNI/NNI logical port. If the logical port is not
performing network-side procedures, then this
value is equal to noSuchName."::={ frMgtVCSigEntry 15}frMgtVCSigNetChanInactive OBJECT-TYPESYNTAXCounter32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times the network-side channel was
declared inactive (i.e., N392 errors in N393
events) for this UNI/NNI logical port. If the
logical port is not performing network-side
procedures, then this value is equal to
noSuchName."::={ frMgtVCSigEntry 16}-- The PVC End-Point Group-- This table is used to identify the traffic parameters-- for a bi-directional PVC segment end-point, and it also-- provides statistics for a PVC segment-- end-point.-- A PVC segment end-point is identified by a UNI/NNI-- logical port index value and DLCI index value.-- If the Frame Relay service provider allows-- the Frame Relay CNM subscriber to create, modify
-- or delete PVCs using SNMP, then this table is used to identify-- and reserve-- the requested traffic parameters of each-- PVC segment end-point. The Connection table-- is used to "connect" the end-points together.-- Not all implementations will support the-- capability of creating/modifying/deleting-- PVCs using SNMP as a feature of Frame Relay-- CNM service.-- Uni-directional PVCs are modeled with zero-- valued traffic parameters in one of the-- directions (In or Out direction) in this table.-- To create a PVC, the following procedures-- shall be followed:-- 1). Create the entries for the PVC segment endpoints in the-- frPVCEndptTable by specifying the traffic parameters-- for the bi-directional PVC segment endpoints.-- As shown in the figure, a point-to-point PVC has-- two endpoints, thus two entries in this table.
-- Uni-directional PVCs are modeled-- with zero valued traffic parameters in one-- direction; all the `In' direction parameters-- for one Frame Relay PVC End-point or-- all the `Out' direction-- parameters for the other Frame Relay PVC-- End-point.-- In ____________________________________ Out-- >>>>>>| |>>>>>>>>-- ______| Frame Relay Network |__________-- Out | | In-- <<<<<<| |<<<<<<<<-- |___________________________________|-- Frame Relay PVC Frame Relay-- End-point PVC End-point-- 2). Go to the Frame Relay Connection Group.
---- The Frame Relay PVC End-point TablefrPVCEndptTable OBJECT-TYPESYNTAXSEQUENCEOF FrPVCEndptEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Frame Relay PVC End-Point table. This table
is used to model a PVC end-point. This table
contains the traffic parameters and statistics for
a PVC end-point."::={ frnetservObjects 3}frPVCEndptEntry OBJECT-TYPESYNTAX FrPVCEndptEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the Frame Relay PVC Endpoint table."INDEX{ ifIndex, frPVCEndptDLCIIndex }
::={ frPVCEndptTable 1}
FrPVCEndptEntry ::=SEQUENCE{
frPVCEndptDLCIIndex
Integer32,
frPVCEndptInMaxFrameSize
Integer32,
frPVCEndptInBc
Integer32,
frPVCEndptInBe
Integer32,
frPVCEndptInCIR
Integer32,
frPVCEndptOutMaxFrameSize
Integer32,
frPVCEndptOutBc
Integer32,
frPVCEndptOutBe
Integer32,
frPVCEndptOutCIR
Integer32,
frPVCEndptConnectIdentifier
Integer32,
frPVCEndptRowStatus
RowStatus,
frPVCEndptRcvdSigStatus
INTEGER,
frPVCEndptInFrames
Counter32,
frPVCEndptOutFrames
Counter32,
frPVCEndptInDEFrames
Counter32,
frPVCEndptInExcessFrames
Counter32,
frPVCEndptOutExcessFrames
Counter32,
frPVCEndptInDiscards
Counter32,
frPVCEndptInOctets
Counter32,
frPVCEndptOutOctets
Counter32}frPVCEndptDLCIIndex OBJECT-TYPESYNTAXInteger32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"The value of this object is equal to the DLCI
value for this PVC end-point."::={ frPVCEndptEntry 1}frPVCEndptInMaxFrameSize OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is the size in octets of
the largest frame relay information field for this
PVC end-point in the ingress direction (into the
frame relay network). The value of
frPVCEndptInMaxFrameSize must be less than or
equal to the corresponding ifMtu for this Frame
Relay UNI/NNI logical port."::={ frPVCEndptEntry 2}frPVCEndptInBc OBJECT-TYPESYNTAXInteger32
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this PVC end-point in the ingress
direction (into the frame relay network)."::={ frPVCEndptEntry 3}frPVCEndptInBe OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this PVC end-point in the ingress direction (into
the frame relay network)."::={ frPVCEndptEntry 4}frPVCEndptInCIR OBJECT-TYPE
SYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this PVC end-
point in the ingress direction (into the frame
relay network)."::={ frPVCEndptEntry 5}frPVCEndptOutMaxFrameSize OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is the size in octets of
the largest frame relay information field for this
PVC end-point in the egress direction (out of the
frame relay network). The value of
frPVCEndptOutMaxFrameSize must be less than or
equal to the corresponding ifMtu for this Frame
Relay UNI/NNI logical port."::={ frPVCEndptEntry 6}frPVCEndptOutBc OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is equal to the
committed burst size (Bc) parameter (measured in
bits) for this PVC end-point in the egress
direction (out of the frame relay network)."::={ frPVCEndptEntry 7}frPVCEndptOutBe OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION
"The value of this object is equal to the excess
burst size (Be) parameter (measured in bits) for
this PVC end-point in the egress direction (out of
the frame relay network)."::={ frPVCEndptEntry 8}frPVCEndptOutCIR OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object is equal to the
committed information rate (CIR) parameter
(measured in bits per second) for this PVC end-
point in the egress direction (out of the frame
relay network)."::={ frPVCEndptEntry 9}frPVCEndptConnectIdentifier OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object is used to associate PVC end-points
as being part of one PVC segment connection. This
value of this object is equal to the value of
frPVCConnectIndex, which is used as one of the
indices into the frPVCConnectTable. The value of
this object is provided by the agent, after the
associated entries in the frPVCConnectTable have
been created."::={ frPVCEndptEntry 10}frPVCEndptRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used to create new rows in this
table, modify existing rows, and to delete
existing rows. To create a new PVC, the entries
for the PVC segment end-points in the
frPVCEndptTable must first be created. Next, the
frPVCConnectTable is used to associate the Frame
Relay PVC segment end-points. In order for the
manager to have the necessary error diagnostics,
the frPVCEndptRowStatus object must initially be
set to `createAndWait'. While the
frPVCEndptRowStatus object is in the
`createAndWait' state, the manager can set each
columnar object and get the necessary error
diagnostics. The frPVCEndptRowStatus object may
not be set to `active' unless the following
columnar objects exist in this row:
frPVCEndptInMaxFrameSize, frPVCEndptInBc,
frPVCEndptInBe, frPVCEndptInCIR,
frPVCEndptOutMaxFrameSize, frPVCEndptOutBc,
frPVCEndptOutBe, and frPVCEndptOutCIR."::={ frPVCEndptEntry 11}frPVCEndptRcvdSigStatus OBJECT-TYPESYNTAXINTEGER{deleted(1),
active(2),inactive(3),none(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the PVC
status received via the local in-channel signaling
procedures for this PVC end-point. This object is
only pertinent for interfaces that perform the
bidirectional procedures. For user-to-network
network side procedures, the value of this object
should be none."::={ frPVCEndptEntry 12}frPVCEndptInFrames OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The number of frames received by the network
(ingress) for this PVC end-point. This includes
any frames discarded by the network due to
submitting more than Bc + Be data or due to any
network congestion recovery procedures."::={ frPVCEndptEntry 13}frPVCEndptOutFrames OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of frames sent by the network (egress)
regardless of whether they are Bc or Be frames for
this PVC end-point."::={ frPVCEndptEntry 14}frPVCEndptInDEFrames OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of frames received by the network
(ingress) with the DE bit set to (1) for this PVC
end-point."::={ frPVCEndptEntry 15}frPVCEndptInExcessFrames OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of frames received by the network
(ingress) for this PVC end-point which were
treated as excess traffic. Frames which are sent
to the network with DE set to zero are treated as
excess when more than Bc bits are submitted to the
network during the Committed Information Rate
Measurement Interval (Tc). Excess traffic may or
may not be discarded at the ingress if more than
Bc + Be bits are submitted to the network during
Tc. Traffic discarded at the ingress is not
recorded in frPVCEndptInExcessFrames. Frames
which are sent to the network with DE set to one
are also treated as excess traffic."::={ frPVCEndptEntry 16}frPVCEndptOutExcessFrames OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of frames sent by the network (egress)
for this PVC end-point which were treated as
excess traffic. (The DE bit may be set to one.)"::={ frPVCEndptEntry 17}frPVCEndptInDiscards OBJECT-TYPESYNTAXCounter32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of frames received by the the network
(ingress) that were discarded due to traffic
enforcement for this PVC end-point."::={ frPVCEndptEntry 18}frPVCEndptInOctets OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of octets received by the network
(ingress) for this PVC end-point. This counter
should only count octets from the beginning of the
frame relay header field to the end of user data.
If the network supporting Frame Relay can not
count octets, then this count should be an
approximation."::={ frPVCEndptEntry 19}
frPVCEndptOutOctets OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of octets sent by the network (egress)
for this PVC end-point. This counter should only
count octets from the beginning of the frame relay
header field to the end of user data. If the
network supporting Frame Relay can not count
octets, then this count should be an
approximation."::={ frPVCEndptEntry 20}-- The Frame Relay PVC Connection Group-- The Frame Relay PVC Connection Group-- is used to model the bi-directional-- PVC segment flows;-- point-to-point PVCs, point-to-multipoint-- PVCs, and multipoint-to-multipoint
-- PVCs.-- This table has read-create access and-- is used to associate PVC end-points-- together as belonging to one connection.-- The frPVCConnectIndex is used to associate-- all the bi-directional flows.-- Not all implementations will support the-- capability of creating/modifying/deleting-- PVCs using SNMP as a feature of Frame Relay-- CNM service.-- Once the entries in the frPVCEndptTable-- are created, the following step are used-- to associate the PVC end-points as belonging-- to one PVC connection:-- 1). Obtain a unique frPVCConnectIndex-- using the frPVCConnectIndexValue object.-- 2). Connect the PVC segment endpoints together-- with the applicable frPVCConnectIndex value-- obtained via-- frPVCConnectIndexValue.-- The entries in this table are created by using
-- the frPVCConnectRowStatus object.-- 3). The agent will provide the value of the-- corresponding instances of-- frPVCEndptConnectIdentifier with the-- the frPVCConnectIndex value.-- 4). Set frPVCConnectAdminStatus to `active' in all-- rows for this PVC segment to-- turn the PVC on.-- For example, the Frame Relay PVC Connection Group-- models a bi-directional, point-to-point PVC segment-- as one entry in this table.-- Frame Relay Network Frame Relay Network-- Low Port ____________________________________ High Port-- | |-- ______| >> from low to high PVC flow >> |____________-- | << from high to low PVC flow << |-- |___________________________________|--
-- The terms low and high are chosen to represent numerical-- ordering of a PVC segment's endpoints for representation-- in this table. That is, the endpoint with the lower value-- of ifIndex is termed 'low', while the opposite endpoint-- of the segment is termed 'high'.-- This terminology is to provide directional information;-- for example the frPVCConnectL2hOperStatus and-- frPVCConnectH2lOperStatus as illustrated above.-- If the Frame Relay Connection table is used to model-- a unidirectional PVC, then one direction (either from low to high-- or from high to low) has its Operational Status equal to down.-- A PVC segment is a portion of a PVC-- that traverses one Frame Relay Network, and-- a PVC segment is identified-- by its two end-points (UNI/NNI logical port index-- value and DLCI index value)-- through one Frame Relay Network.frPVCConnectIndexValue OBJECT-TYPESYNTAXINTEGER(0..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains an appropriate value to be
used for frPVCConnectIndex when creating entries
in the frPVCConnectTable. The value 0 indicates
that no unassigned entries are available. To
obtain the frPVCConnectIndex value for a new
entry, the manager issues a management protocol
retrieval operation to obtain the current value of
this object. After each retrieval, the agent
should modify the value to the next unassigned
index."::={ frnetservObjects 4}-- The Frame Relay PVC Connection TablefrPVCConnectTable OBJECT-TYPE
SYNTAXSEQUENCEOF FrPVCConnectEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Frame Relay PVC Connect table. A bi-
directional PVC segment is modeled as one entry in
this table."::={ frnetservObjects 5}frPVCConnectEntry OBJECT-TYPESYNTAX FrPVCConnectEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the Frame Relay PVC Connect table.
This entry is used to model a PVC segment in two
directions."INDEX{ frPVCConnectIndex,
frPVCConnectLowIfIndex, frPVCConnectLowDLCIIndex,
frPVCConnectHighIfIndex, frPVCConnectHighDLCIIndex }::={ frPVCConnectTable 1}
FrPVCConnectEntry ::=SEQUENCE{
frPVCConnectIndex
Integer32,
frPVCConnectLowIfIndex
IfIndex,
frPVCConnectLowDLCIIndex
Integer32,
frPVCConnectHighIfIndex
IfIndex,
frPVCConnectHighDLCIIndex
Integer32,
frPVCConnectAdminStatus
INTEGER,
frPVCConnectL2hOperStatus
INTEGER,
frPVCConnectH2lOperStatus
INTEGER,
frPVCConnectL2hLastChange
TimeStamp,
frPVCConnectH2lLastChange
TimeStamp,
frPVCConnectRowStatus
RowStatus}frPVCConnectIndex OBJECT-TYPESYNTAXInteger32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The value of this object is equal to the
frPVCConnectIndexValue obtained to uniquely
identify this PVC segment connection."::={ frPVCConnectEntry 1}frPVCConnectLowIfIndex OBJECT-TYPESYNTAXIfIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The value of this object is equal to MIB II's
ifIndex value of the UNI/NNI logical port for this
PVC segment. The term low implies that this PVC
segment end-point has the numerically lower
ifIndex value than the connected/associated PVC
segment end-point. If the value is equal to zero,
then this logical port is not a Frame Relay
UNI/NNI logical port."::={ frPVCConnectEntry 2}frPVCConnectLowDLCIIndex OBJECT-TYPESYNTAXInteger32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The value of this object is equal to the DLCI
value for this end-point of the PVC segment. If
the value is equal to zero, then this endpoint of
the PVC segment is not a Frame Relay connection."::={ frPVCConnectEntry 3}frPVCConnectHighIfIndex OBJECT-TYPE
SYNTAXIfIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The value of this object is equal to MIB II's
ifIndex value for the UNI/NNI logical port for
this PVC segment. The term high implies that this
PVC segment end-point has the numerically higher
ifIndex value than the connected/associated PVC
segment end-point."::={ frPVCConnectEntry 4}frPVCConnectHighDLCIIndex OBJECT-TYPESYNTAXInteger32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The value of this object is equal to the egress
DLCI value for this end-point of the PVC segment."::={ frPVCConnectEntry 5}
frPVCConnectAdminStatus OBJECT-TYPESYNTAXINTEGER{active(1),inactive(2),testing(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The value of this object identifies the desired
administrative status of this bi-directional PVC
segment. The active state means the PVC segment
is currently operational; the inactive state means
the PVC segment is currently not operational; the
testing state means the PVC segment is currently
undergoing a test. This state is set by an
administrative entity. This value affects the PVC
status indicated across the ingress NNI/UNI of
both end-points of the bi-directional PVC segment.
When a PVC segment connection is created using
this table, this object is initially set to
`inactive'. After the frPVCConnectRowStatus
object is set to `active' (and the
corresponding/associated entries in the
frPVCEndptTable have their frPVCEndptRowStatus
object set to `active'), the
frPVCConnectAdminStatus object may be set to
`active' to turn on the PVC segment connection."::={ frPVCConnectEntry 6}frPVCConnectL2hOperStatus OBJECT-TYPESYNTAXINTEGER{active(1),inactive(2),testing(3),unknown(4)
}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the current
operational status of the PVC segment connection
in one direction; (i.e., in the low to high
direction). The active state means it is
currently operational; the inactive state means it
is currently not operational; the testing state
means it is currently undergoing a test; the
unknown state means the status of it currently can
not be determined. This value affects the PVC
status indicated across the ingress NNI/UNI (low
side) of the PVC segment."::={ frPVCConnectEntry 7}frPVCConnectH2lOperStatus OBJECT-TYPESYNTAXINTEGER{
active(1),inactive(2),testing(3),unknown(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object identifies the current
operational status of the PVC segment connection
in one direction; (i.e., in the high to low
direction). The active state means it is
currently operational; the inactive state means it
is currently not operational; the testing state
means it is currently undergoing a test; the
unknown state means the status of it currently can
not be determined. This value affects the PVC
status indicated across the ingress NNI/UNI (high
side) of the PVC segment."::={ frPVCConnectEntry 8}frPVCConnectL2hLastChange OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of MIB II's sysUpTime object at the
time this PVC segment entered its current
operational state in the low to high direction.
If the current state was entered prior to the last
re-initialization of the proxy-agent, then this
object contains a zero value."::={ frPVCConnectEntry 9}frPVCConnectH2lLastChange OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The value of MIB II's sysUpTime object at the
time this PVC segment entered its current
operational state in the high to low direction.
If the current state was entered prior to the last
re-initialization of the proxy-agent, then this
object contains a zero value."::={ frPVCConnectEntry 10}frPVCConnectRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status of this entry in the
frPVCConnectTable. This variable is used to
create new connections for the PVC end-points and
to change existing connections of the PVC end-
points. This object must be initially set to
`createAndWait'. In this state, the agent checks
the parameters in the associated entries in the
frPVCEndptTable to verify that the PVC end-points
can be connected (i.e., the In parameters for one
PVC end-point are equal to the Out parameters for
the other PVC end-point). This object can not be
set to `active' unless the following columnar
object exist in this row: frPVCConnectAdminStatus.
The agent also supplies the associated value of
frPVCConnectIndex for the frPVCEndptConnectIdentifier
instances. To turn on a PVC segment connection, the
frPVCConnectAdminStatus is set to `active'."::={ frPVCConnectEntry 11}-- The Frame Relay Accounting Groups-- The groups are the following:-- Accounting on a PVC basis-- Accounting on an Interface/Logical Port basis-- The Accounting on a Frame Relay PVC basis Group-- The accounting information is collected for a PVC-- segment end-point.frAccountPVCTable OBJECT-TYPESYNTAXSEQUENCEOF FrAccountPVCEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Frame Relay Accounting PVC table. This table
is used to perform accounting on a PVC segment
end-point basis."::={ frnetservObjects 6}frAccountPVCEntry OBJECT-TYPESYNTAX FrAccountPVCEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the Frame Relay Accounting PVC
table."INDEX{ ifIndex, frAccountPVCDLCIIndex }::={ frAccountPVCTable 1}
FrAccountPVCEntry ::=
SEQUENCE{
frAccountPVCDLCIIndex
Integer32,
frAccountPVCSegmentSize
Integer32,
frAccountPVCInSegments
Counter32,
frAccountPVCOutSegments
Counter32}frAccountPVCDLCIIndex OBJECT-TYPESYNTAXInteger32MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The value of this object is equal to the DLCI
value for this PVC segment end-point."::={ frAccountPVCEntry 1}frAccountPVCSegmentSize OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The value of this object is equal to the Segment
Size for this PVC segment end-point."::={ frAccountPVCEntry 2}frAccountPVCInSegments OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object is equal to the number
of segments received by this PVC segment end-
point."::={ frAccountPVCEntry 3}frAccountPVCOutSegments OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The value of this object is equal to the number
of segments sent by this PVC segment end-point."::={ frAccountPVCEntry 4}-- The Accounting on a Frame Relay Logical Port basis GroupfrAccountLportTable OBJECT-TYPESYNTAXSEQUENCEOF FrAccountLportEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The Frame Relay Accounting Logical Port table.
This table is used to perform accounting on a
UNI/NNI Logical Port basis."::={ frnetservObjects 7}frAccountLportEntry OBJECT-TYPESYNTAX FrAccountLportEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"An entry in the Frame Relay Accounting Logical
Port table."INDEX{ ifIndex }::={ frAccountLportTable 1}
FrAccountLportEntry ::=SEQUENCE{
frAccountLportSegmentSize
Integer32,
frAccountLportInSegments
Counter32,
frAccountLportOutSegments
Counter32}frAccountLportSegmentSize OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object is equal to the Segment
Size for this UNI/NNI logical port."::={ frAccountLportEntry 1}frAccountLportInSegments OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object is equal to the number
of segments received by this UNI/NNI logical
port."::={ frAccountLportEntry 2}frAccountLportOutSegments OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of this object is equal to the number
of segments sent by this UNI/NNI logical port."
::={ frAccountLportEntry 3}-- Frame Relay Network Service TRAPSfrPVCConnectStatusChange NOTIFICATION-TYPEOBJECTS{ frPVCConnectIndex,
frPVCConnectLowIfIndex, frPVCConnectLowDLCIIndex,
frPVCConnectHighIfIndex, frPVCConnectHighDLCIIndex,
frPVCConnectL2hOperStatus, frPVCConnectH2lOperStatus,
frPVCEndptRcvdSigStatus }STATUScurrentDESCRIPTION"This trap indicates that the indicated PVC has
changed state. This trap is not sent if an FR-UNI
changes state; a linkDown or linkUp trap should be
sent instead."::={ frnetservTraps 1}
-- Conformance InformationfrnetservConformance OBJECTIDENTIFIER::={ frnetservMIB 3}frnetservGroups OBJECTIDENTIFIER::={ frnetservConformance 1}frnetservCompliances OBJECTIDENTIFIER::={ frnetservConformance 2}-- Compliance StatementsfrnetservCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for SNMPv2 entities
which have Frame Relay Network Service Interfaces."MODULE-- this moduleMANDATORY-GROUPS{ frnetservLportGroup,
frnetservMgtVCSigGroup,
frnetservPVCEndptGroup,
frnetservPVCConnectGroup }GROUP frnetservAccountPVCGroup
DESCRIPTION"This group is optional for Frame Relay interfaces.
It is
mandatory if and only if accounting is performed
on a PVC
basis this
Frame Relay interface."GROUP frnetservAccountLportGroup
DESCRIPTION"This group is optional for Frame Relay interfaces.
It is
mandatory if and only if accounting is
performed on a
logical port basis this
Frame Relay interface."OBJECT frPVCEndptInMaxFrameSize
SYNTAXInteger32MIN-ACCESSread-only
DESCRIPTION"Write access is not required."OBJECT frPVCEndptInBc
SYNTAXInteger32MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCEndptInBe
SYNTAXInteger32MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCEndptInCIR
SYNTAXInteger32MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCEndptOutMaxFrameSize
SYNTAXInteger32
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCEndptOutBc
SYNTAXInteger32MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCEndptOutBe
SYNTAXInteger32MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCEndptOutCIR
SYNTAXInteger32MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCEndptConnectIdentifier
SYNTAXInteger32MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCEndptRowStatus
SYNTAXINTEGER{ active(1)}-- subset of RowStatusMIN-ACCESSread-onlyDESCRIPTION"Write access is not required, and only one of the
six enumerated values for the RowStatus textual
convention need be supported, specifically:
active(1)."OBJECT frPVCConnectAdminStatus
SYNTAXINTEGER{
active(1),
inactive(2),
testing(3)}MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCConnectRowStatus
SYNTAXINTEGER{ active(1)}-- subset of RowStatusMIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT frPVCConnectRowStatus
SYNTAXINTEGER{ active(1)}-- subset of RowStatus
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required, and only one of the
six enumerated values for the RowStatus textual
convention need be supported, specifically:
active(1)."::={ frnetservCompliances 1}-- Units of ConformancefrnetservLportGroup OBJECT-GROUPOBJECTS{ frLportNumPlan, frLportContact, frLportLocation,
frLportType,
frLportAddrDLCILen, frLportVCSigProtocol,
frLportVCSigPointer }STATUScurrentDESCRIPTION"A collection of objects providing information applicable
to a Frame Relay Logical Port."
::={ frnetservGroups 1}frnetservMgtVCSigGroup OBJECT-GROUPOBJECTS{ frMgtVCSigProced,
frMgtVCSigUserN391,
frMgtVCSigUserN392,
frMgtVCSigUserN393,
frMgtVCSigUserT391,
frMgtVCSigNetN392,
frMgtVCSigNetN393,
frMgtVCSigNetT392,
frMgtVCSigNetnN4,
frMgtVCSigNetnT3,
frMgtVCSigUserLinkRelErrors,
frMgtVCSigUserProtErrors,
frMgtVCSigUserChanInactive,
frMgtVCSigNetLinkRelErrors,
frMgtVCSigNetProtErrors,
frMgtVCSigNetChanInactive }
STATUScurrentDESCRIPTION"A collection of objects providing information
applicable to the
Local In-Channel Signaling Procedures used for a
UNI/NNI logical port."::={ frnetservGroups 2}frnetservPVCEndptGroup OBJECT-GROUPOBJECTS{ frPVCConnectIndexValue,
frPVCEndptInMaxFrameSize, frPVCEndptInBc,
frPVCEndptInBe, frPVCEndptInCIR,
frPVCEndptOutMaxFrameSize, frPVCEndptOutBc,
frPVCEndptOutBe, frPVCEndptOutCIR,
frPVCEndptConnectIdentifier, frPVCEndptRowStatus,
frPVCEndptRcvdSigStatus, frPVCEndptInFrames,
frPVCEndptOutFrames, frPVCEndptInDEFrames,
frPVCEndptInExcessFrames, frPVCEndptOutExcessFrames,
frPVCEndptInDiscards,
frPVCEndptInOctets, frPVCEndptOutOctets }STATUScurrentDESCRIPTION"A collection of objects providing information application
to a Frame Relay PVC end-point."::={ frnetservGroups 3}frnetservPVCConnectGroup OBJECT-GROUPOBJECTS{ frPVCConnectAdminStatus, frPVCConnectL2hOperStatus,
frPVCConnectH2lOperStatus, frPVCConnectL2hLastChange,
frPVCConnectH2lLastChange,
frPVCConnectRowStatus }STATUScurrent
DESCRIPTION"A collection of objects providing information applicable
to a Frame Relay PVC connection."::={ frnetservGroups 4}frnetservAccountPVCGroup OBJECT-GROUPOBJECTS{ frAccountPVCSegmentSize, frAccountPVCInSegments,
frAccountPVCOutSegments }STATUScurrentDESCRIPTION"A collection of objects providing accounting
information application
to a Frame Relay PVC end-point."::={ frnetservGroups 5}frnetservAccountLportGroup OBJECT-GROUPOBJECTS{ frAccountLportSegmentSize, frAccountLportInSegments,
frAccountLportOutSegments }STATUScurrentDESCRIPTION"A collection of objects providing accounting
information application
to a Frame Relay logical port."::={ frnetservGroups 6}END